How do I resolve Dell error code 0141?

Troubleshooting Methods to Resolve Dell Inspiron Error code 0141

  1. Press and hold the Fn key on your Dell Inspiron laptop and while holding the Fn key, press the ‘Power’ button.
  2. The system enters into the diagnostic mode. You can follow along with the wizard and allow the diagnostic tool to run a scan.

How do I fix a Dell boot error?

Table of Contents:

  1. Verify the Computer Finishes Initial Power-Up (POST)
  2. Unplug all devices, and perform a hard reset.
  3. Run a Computer Diagnostic.
  4. Check for Specific Error Messages.
  5. Reset the BIOS to Default Values.
  6. Safe Mode Troubleshooting.
  7. Virus and Malware Troubleshooting.
  8. Reset your Windows 10 Operating System.

How do I fix the error code on my Dell hard drive?

Fix or Get Rid of the Dell Hard Drive Error 2000-0142 to Recover Data

  1. Connect the hard drive to another computer. Pull out the affected drive.
  2. Use Windows installation media to run CHKDSK command. MBR holds information about the location of the installed OS.
  3. Reinstall Windows.

How do I test my Dell laptop hard drive?

How do I run Dell Diagnostics?

  1. Restart the computer.
  2. As the computer boots, press F12 when the Dell Splash Screen appears.
  3. When the Boot menu appears, highlight the Boot to Utility Partition option or the Diagnostics option and then press to start the 32-bit Dell Diagnostics.
  4. Press the Tab key to highlight Test System.

What does error code 2000 0142 mean?

To put it simply, this error means that the ePSA could not successfully read information from the hard drive. Faulty or misaligned cabling in your computer’s case, connecting your hard drive to the motherboard. Corrupted data or MBR (Master Boot Record) on the hard disk, causing the device to crash.

How do I fix error 2000 0146 on my hard drive?

Ans: To fix the error code 2000-0146, you can try the following methods:

  1. Scan your system.
  2. Run Disk Checkup.
  3. Repair PC Registry.
  4. Run PSA (Pre-Boot System Assessment) Diagnostics.
  5. Reset BIOS Settings.
  6. Restore PC in Safe Mode.
  7. Perform a Clean Boot.

How do I reset a computer that won’t boot?

Since you can’t start Windows, you can run System Restore from Safe Mode:

  1. Start the PC and press the F8 key repeatedly until the Advanced Boot Options menu appears.
  2. Select Safe Mode with Command Prompt.
  3. Press Enter.
  4. Type: rstrui.exe.
  5. Press Enter.
  6. Follow the wizard instructions to choose a restore point.

How do you hard reset a Dell laptop?

Hard Reboot

  1. Press and hold the power button on the front of the computer for approximately 5 seconds. The computer will shut off. No lights should be near the power button. If lights are still on, you can unplug the power cord to the computer tower.
  2. Wait 30 seconds.
  3. Push the power button to turn the computer on again.

How do I fix error code 2000 0146?

What should a user do to preserve BIOS settings before recovering the system?

Press and hold the CTRL + ESC key on the keyboard until the BIOS Recovery page appears. On the BIOS Recovery screen, select Reset NVRAM (if available) and press the Enter key. Select Disabled and press the Enter key to save the current BIOS settings.

How do I fix error code 2000 0511?

Troubleshooting Steps to Fix Dell Error Code 2000-0511:-

  1. 1:- Modify Fan configuration settings.
  2. 2:- Reseat the Hard Drive.
  3. 3:- Run Diagnostics on the Computer.
  4. 4:- Update BIOS.

What does DST log error code 2000-0146 mean?

Let me first appreciate the fact that you have tried the steps yourself to isolate the problem. Error code: 2000-0146 (DST Log contains previous errors) refers to previous errors in the hard drive which might not really be a hardware failure.

What does Dell error code 2000-0146 mean?

If the DST from the Utility Partition does not indicate a failure of the drive, Dell consider’s the error to have been corrected and the drive does not need to be replaced. 2000-0146 (Drive Self Test) can also occur if you have not provided a write-able Disc to check the optical drive.

What does the 2000-0146 PSA Code mean?

After the 2000-0146 (Drive Self Test) code occurs, you don’t have any option to continue running the PSA, only to reboot the system. Moreover, I have run the Dell 32-bit Diagnostics from a CD and the Hard drive tests all pass without any error (it is a new drive).

What does it mean when your hard drive says 2000-0146?

And eventually, your hard drive may become usable and all your data stored on the hard drive could get lost. So, when you get the error code 0146 or error code 2000-0146, you should pay attention to it and take measures.

https://www.youtube.com/watch?v=EMHJmA3Nkr4