How much does it cost to rip up carpet and stain concrete?
Typically, staining concrete costs between $7 and $15 per square foot. Contractors charge between $2 and $4 per square foot for a simple stain job and between $12 and $25 per square foot for a high-end design.
How do you remove carpet from concrete?
Use a sharp utility knife to cut through the carpet to form strips a couple of feet wide, then loosen each strip by whacking at the edges with the shovel- scraper. When you get enough carpet loose to get a good grip on it, you can usually pull it off.
How do you paint a concrete floor after removing carpet?
- Step 1: Tear out carpet & carpet pad.
- Step 2: Remove tack strips.
- Step 3: Clean off paint and adhesive.
- Step 4: Fill holes & cracks with concrete filler.
- Step 5: Sand down or scrape high spots & Leftover paint/glue.
- Step 6: Analyze trim (Remove and lower or keep and caulk?)
- Step 7: Clean concrete floors (sweep, mop, vacuum)
How do you remove carpet glue from concrete before staining?
How To Remove Carpet Glue From Concrete Floor
- Step 1: Scrape the concrete glue. Scrape off as much of the concrete glue as possible.
- Step 2: Apply boiling water.
- Step 3: Scrub the loosened glue.
- Step 4: Apply glue remover.
- Step 5: Sand the floor.
- Step 6: Troubleshoot.
Can you rip up carpet yourself?
When hiring someone to replace the carpet or install new flooring, removing old carpet yourself and preparing the subfloor can save you money. DIY carpet removal is a simple process that requires only a few carpet tools and a moderate amount of strength.
Does stained concrete increase home value?
Getting concrete floor coatings or a decorative concrete overlay is not a luxury – it’s an investment that can pay off over time. Not only will the investment improve your enjoyment of the home and reduce your maintenance, but it will also improve the value of your home.
Do I have to remove old carpet glue?
Ripping up old carpeting is no small task, but removing the glue used to secure it to the subfloor is a major job all on its own. If you suspect the adhesive on your floor could contain asbestos, do not attempt to remove it yourself; contact an asbestos abatement professional.
Do I need to remove carpet glue before laying vinyl?
LVT Floor (tiles or planks): Yes. If the floor is glued down, be sure you remove all of the adhesive before installing laminate flooring.
Do you have to remove carpet adhesive?
How hard is it to pull up carpet?
Pulling up carpet is a relatively easy task although when rolled up a carpet can be very heavy, bulky and difficult to move. It’s usually easier to cut carpet from the back so when cutting it into small sections, fold a section over revealing the back then slice through the woven backing with a utility or carpet knife.
What’s the best way to remove carpet from concrete?
When removing carpet padding from concrete, use a floor scraper to remove the pieces of padding that remain stuck to the floor. Tough spots might require commercial adhesive remover or a power oscillating tool. Use pliers to pull padding staples when removing carpet from stairs.
How to remove carpet from stairs at Home Depot?
How to pull up carpet from stairs: 1 Begin at the top of the stairs. 2 Pry up the metal nosing and remove it, if present. 3 While wearing work gloves, grab the cut end of carpet and pull it from the stairs. 4 If the carpet is in one continuous piece, cut off manageable pieces as you remove it. 5 Roll, duct tape, bag and remove the old carpet.
How can I replicate the look of a polished concrete floor?
An integrally colored microtopping, troweled smooth and sealed with a urethane, was the solution to replicating the look of a polished concrete floor. Contractor develops a process to cover old wood floors and decks with decorative stamped concrete. Concrete floor video showing how you can install colorful and durable.
What do you use to remove carpet from subfloor?
Some may come loose when you pull up the pad, but most will remain stuck in the floor. If you have a concrete subfloor, the padding is glued into place. Use pliers to remove the staples near the walls. A long-handled floor scraper with a sharp blade can make quick work of the staples.