What is the best wood for a Native American flute?

Western Red Cedar is the quintessential Native American love flute wood. Very light to hold, this flute-wood produces a classic warm, rich and resonant tone.

How do you make a wooden flute?

Measure the length between the finger holes with a flute calculator. Mark where each hole should be and make sure that these will fit your pole. Clamp the bamboo down and drill the embouchure. Begin drilling with the 2mm (0.078 inches) drill bit and increase to a larger drill bit just like the 8 mm (0.315 inches).

How many holes does a Native American flute have?

Native American flutes typically have either five or six finger holes, but any particular instrument may have from zero to seven finger holes.

What type of wood is used to make a Navajo flute?

This traditional Navajo flute is carved from natural cedar wood by Donald Coolidge. It is beautifully finished with a bird and white leather stripping. Coolidge, a Navajo Native American carver and flute player, he makes certain each flutes sounds beautiful or he destroys them and carves a new one.

What is a Native American flute called?

American Indian courting flute
The Native American flute has many other names.: American Indian courting flute, courting flute, Grandfather’s flute, Indian flute, love flute, Native American courting flute, Native American love flute, Native American style flute (see the Indian Arts And Crafts Act), North American flute, Plains flute, and Plains …

How difficult is Native American flute?

Playing the Native American style flute is not difficult. With few minutes of practice, you can already make simple melodies. Within an hour you can memorize a couple of songs, and after few weeks of regular practice you can play nicely your own songs.

How do wood flutes work?

A flute produces sound when a stream of air directed across a hole in the instrument creates a vibration of air at the hole. The airstream creates a Bernoulli or siphon. This excites the air contained in the usually cylindrical resonant cavity within the flute.

How much does a wooden flute cost?

Beginner flutes often range between $150 and $700, although you can get some for even less than $70. As a beginner, you should start with something less expensive. This is because you will eventually upgrade to a higher level.

Is it hard to play Native American flute?

When it comes to playing music the Native American style flute is probably the easiest instrument – asside from beating a drum – that there is. To learn to make a decent sound and be able to make some melodic runs up and down the scale will take a about two hours.

Did Native Americans really play flutes?

The Native American flute has been reported to be the third oldest known musical instrument in the world, with bone flutes dating back over 60,000 years. Drums were discovered first, and then various rattles were made, followed by bone whistles.

What is the best wood for flutes?

Basically, there is no such thing as the best wood for Native American flute. It does matter, though, for both players and makers. Less experienced woodworkers will prefer softwood, such as pine or cedar, since hardwood, such as walnut, is harder to work with.

What wood is good for flutes?

Boxwood was probably the preferred material for making the classical flute when Boehm came along, but Boehm turned to tropical hardwoods like Ebony, Cocobolo and Grenadilla wood in addition to silver.

What are the measurements of a flute?

The modern flute is about 26 inches in length with and inside diameter of about 3/4″, open at one end. The embouchure at which the edgetone is produced is near one end and constitutes a second open end, making the flute an open cylinder in harmonic content.

How do you make a flute?

Instructions on How to Make a Flute. Measure 5 1/2 cm from the end and mark. Continue the line another 1 1/2 cm and mark again. Between these two marks is where the wind-way will be cut out. Continue along the line another 8 cm and mark, then 7mm and mark again this 7mm is the area where you will cut the first finger hole.

What is Native American flute?

Awards ceremonies and awards. The Native American flute is a flute that is held in front of the player, has open finger holes, and has two chambers: one for collecting the breath of the player and a second chamber which creates sound. The player breathes into one end of the flute without the need for an embouchure.

What is a wood flute?

A wooden flute is a musical instrument. It can be used to play notes to guess the passtune. Improvising with it will exercise your dexterity. Also, if the player has enough experience and dexterity, improvising with it will make nearby snakes peaceful.