What is the default IP of a Netgear switch?

192.168.0.239
You can access and configure the switch directly through its web-based user interface by entering the switch’s IP address in the address bar of a browser. The default IP address of the switch is 192.168. 0.239.

How do I log into my Netgear Prosafe switch?

Open a web browser. Type the IP address of the switch into the address bar of the web browser and press Enter. Type the admin password of the switch (the default password is password) and click Login.

How do I reset my Netgear Prosafe m4100?

To reset a smart switch using the Factory Default button:

  1. Locate the recessed button that is marked Factory Default or Factory Defaults on the back or bottom panel of your device.
  2. Insert a straightened paper clip or a similar device into the hole of the Factory Default button and hold for two to three seconds.

How do I find the IP address of my Smart switch?

Click DHCP Status. e. On the CLIENT TABLE, in the MAC Address column look for the MAC address of the switch (it should match the one printed on the switch’s box). Beside it, you should see the IP address that has been assigned to the switch.

How do I configure NETGEAR switch?

Download the latest firmware for your switch from the NETGEAR support site and install it. Connect a computer to your switch’s local management interface and enable Insight management mode. Add your switch to Insight and start configuring it. (Optional) Configure settings that cannot be managed in Insight.

Do unmanaged switches have IP addresses?

To summarize, unmanaged and layer 2 switches do not have an IP address, whereas managed and layer 3 switches do. Having an IP address assigned to your switch provides you with a way of connecting to it remotely and perform any configuration that is needed.

How do I console my Netgear switch?

Select a console port using the console switch on the rear panel:

  1. Select the mini USB port on the rear panel (cable included) as the console port by pushing the slide switch to the left.
  2. Select the DB9 (cable not included) on the rear panel as the console port by pushing the slide switch to the right.

DO network switches have IP addresses?

What are the steps to configure a switch?

  1. Step 1: Inspect your hardware. Check the model number of your shiny new switch.
  2. Step 2: Set up management IP.
  3. Step 3: Check VTP revision number.
  4. Step 4: Configure access ports.
  5. Step 5: Configure trunk ports.
  6. Step 6: Configure access ports.
  7. Step 7: Set up VTY line config.

How does a Netgear switch work?

A switch is used in a wired network to connect to other devices using Ethernet cables. The switch allows each connected device to talk to the others. Wireless-only networks do not use switches because devices such as wireless routers and adapters communicate directly with one another.

Can switches have IP addresses?

But since the switch does not have the capability to assign IP addresses, the computers connected to it will not be able to communicate with each other. They will get an Automatic Private IP Address (APIPA). You need to assign a static IP address to your computers.

What is the default IP address of my Netgear smart managed?

By default, your NETGEAR Smart Managed Plus, Smart Managed Pro, or Insight Managed Smart Cloud switch attempts to get a dynamic IP address using DHCP. If your switch is using a static IP address, you can access it by opening your web browser and typing 192.168.0.239 in the address bar.

Where can I find the correct IP address for my NetGear switch?

Visit your switch’s product support page to find the correct software for your switch. Note: Make sure that the computer you are using is connected to the switch with an Ethernet cable. The computer that you are using must have an IP address on the same network as the switch’s IP address.

Where can I find the Netgear managed switch user manual?

350 East Plumeria Drive San Jose, CA 95134 USA April 2015 202-10967-02 M4100 Series Managed Switch User Manual Version 10.0.2 2 M4100 Series Managed Switch Support Thank you for selecting NETGEAR products. After installing your device, locate the serial number on the label of your product and use it to register your product at

Which is the user guide for the m4100 switch?

Online Help > User Guide M4100 Command Line Interface Manual. Refer to the M4100 Command Line Interface Manual for information about the command structure. This provides information about the CLI commands used to configure the switch. It provides CLI descriptions, syntax, and default values.