What does Service Tire Monitor System mean on a GMC?
Whenever your car says service tire monitor system, this means that more than likely you have a bad tire pressure monitor sensor (TPMS). Don’t worry this light isn’t going to hurt your car at all. This warning is just letting you know something is wrong with the TPMS.
What does it mean when it says Service Tire Monitor System?
The purpose of the TPMS (Tire Pressure Monitoring System) is to alert you when tire pressure is too low and could create unsafe driving conditions. If the light is illuminated, it means your tires could be underinflated, which can lead to undue tire wear and possible tire failure.
How do I fix my GMC Service Tire Monitor System?
Starting with the vehicle off, turn your key to the “On” position, but don’t start the vehicle. Find the TPMS reset button (check your manual if you need help), and hold it until the tire pressure light blinks three times. Then, start the car and wait 20 minutes for the tire pressure light to reset.
How do you reset the tire pressure sensor on a 2009 GMC Yukon?
Follow these instructions to get started:
- Turn the ignition key to the “ON” position without starting the engine.
- Press the VEHICLE INFORMATION button repeatedly until you see the RELEARN TIRE POSITIONS message on the display.
- Press and hold the ✓ button to enter the relearn mode.
- Activate the TPMS sensor.
How do I turn off my service tire monitor?
With the vehicle off, turn the key to the “on” position, but don’t start the car. Hold the TPMS reset button until the tire pressure light blinks three times, then release it. Start the car and wait 20 minutes for the sensor to refresh. The TPMS reset button is usually located beneath the steering wheel.
How much does it cost to service tire monitor?
The service kit costs $5-$10 per wheel on most vehicles. A special TPMS tool and additional time are also needed to check and reset the sensor system. In the event pressure sensors need to be replaced, the cost ranges from $50-$250 each depending on vehicle type.
How do I reset the service tire monitor?
Press the TPMS reset button and hold it until the light blinks three times, then release it. Start the car and let it run for 20 minutes to reset the sensor. You’ll usually find the tire pressure monitor reset button beneath the steering wheel. Check your user’s manual if you’re having trouble locating it.
How do you reset the tire monitor on a 2008 GMC Yukon?
GMC Yukon (2008 – 2012) TPMS Reset Procedure
- Apply parking brake.
- Press and hold unlock and lock buttons on the keyless entry transmitter until horn sounds, and then LF turn signal will become illuminated.
- Starting with LF tire, increase/decrease tire pressure until horn sounds.
Where is the reset button for the TPMS?
beneath the steering wheel
The TPMS reset button is usually located beneath the steering wheel. If you are unable to find it, refer to your vehicle’s owner’s manual. Inflate all tires to 3 PSI over their recommended amount, then deflate them completely. Be sure to include the spare tire, as it may have a sensor as well.
Can you disable TPMS?
The U.S. Department of Transportation has mandated that all vehicles manufactured after 2008 include a tire pressure monitoring system (TPMS). Although you cannot disable the TPMS in a General Motors (GM) vehicle, you can reset the system if you recently checked your tires and inflated them properly.
What kind of tire pressure sensor does GMC Yukon have?
Yukon is also available as the Yukon XL in the 7-seater version and is therefore identical to the Chevrolet Suburban. If you replacing a spare tire with a road tire containing the TPMS sensor on your GMC Yukon, the system will detect a malfunction and the low tire pressure warning light will blink.
How long does it take to reset TPMs on GMC Yukon?
Time needed: 7 minutes. If you have 2007 2008 2009 2010 GMC Yukon, you can reset the TPMS by increasing or decreasing the tire pressure without using tools. Follow these instructions to get started:
How can I tell if I have a service tire monitor?
On vehicles without a driver information center, you will know you have a code set if you turn the key on, without starting the engine, and the TPMS light blinks for one minute and then stays on solid with a Service Tire Monitor System message (on vehicles equipped with a DIC).
How to service the GM tire pressure monitoring system?
Servicing GM Tire Pressure Monitoring Systems 1. Set the parking brake. 2. Turn the ignition switch to ON/RUN with the engine off. 3. Press and hold the keyless entry fob transmitter’s LOCK and UNLOCK buttons, at the same time, for about five seconds… 4. Starting with the left front tire, active